Product Description
Product Description
GWSP Oil free Scroll Vacuum Pump
Working principle:
GWSP oil free scroll vacuum pump is constructed with pump head assembly, crank pin assembly, bracket assembly, air flush assembly,and exhaust valve assembly.Two spiral cylinders, 1 offset and orbiting against the other fixed with an offset of 180° to form several crescent-shaped pockets of different sizes. By means of an eccentric drive, the orbiting scroll is made to orbit about the fixed scroll, reducing the volume of the pockets and compressing gas from outside towards the inside thereby pumping the gas from vacuum chamber.
Basic informations:
1) Model: GWSP150 Oil free scroll vacuum pump
2) Ultimate vacuum pressure: 6.0Pa/0.06 mbar (abs.)
3) Max suction capacity: 50Hz-2.0L/s 60Hz-2.4L/s
Safety Precautions:
The GWSP series oil free scroll vacuum pumps are suitable for clean processes only.
Do not pump toxic, explosive, flammable or corrosive substances or substances which contain chemicals, solvents or particles.GEOWELL will not perform maintenance work on pumps which have used special gases or other hazardous substances.
Be sure the inlet gas temperature must be lower than 122 °F.
Technical Specifications
| Model | GWSP40 | GWSP75 | GWSP150 | GWSP300 | GWSP600 | GWSP1000 | ||
| Pumping Speed | 50Hz | l/s | 0.5 | 1.0 | 2.0 | 4.3 | 8.7 | 16.6 |
| m3/h | 1.8 | 3.6 | 7.2 | 15.5 | 31.3 | 59.8 | ||
| cfm | 1.1 | 2.1 | 4.3 | 9.3 | 18.7 | 35.8 | ||
| 60Hz | l/s | 0.6 | 1.2 | 2.4 | 5.1 | 10.4 | 20.0 | |
| m3/h | 2.2 | 4.3 | 8.6 | 18.3 | 37.4 | 71.6 | ||
| cfm | 1.3 | 2.5 | 5.1 | 10.9 | 22.3 | 42.8 | ||
| Ultimate Pressure | Torr | ≤1.1*10-1 | ≤6.0*10-2 | ≤4.5*10-2 | ≤1.9*10-2 | ≤7.5*10-3 | ≤7.5*10-3 | |
| psi | ≤2.2*10-3 | ≤1.2*10-3 | ≤9.0*10-4 | ≤3.8*10-4 | ≤1.5*10-4 | ≤1.5*10-4 | ||
| Pa | ≤15 | ≤8 | ≤6 | ≤2.6 | ≤1 | ≤1 | ||
| mbar | ≤1.5*10-1 | ≤8.0*10-2 | ≤6.0*10-2 | ≤2.6*10-2 | ≤1.0*10-2 | ≤1.0*10-2 | ||
| Noise Level | dB(A) | ≤54 | ≤57 | ≤57 | ≤60 | ≤61 | ≤65 | |
| Leakage | mbar·l/s | 1*10-7 | ||||||
| Max. Inlet/Exhaust Pressure | MPa | 0.1 / 0.13 | ||||||
| Ambient Operation Temp. | ºF | 41~104 | ||||||
| Motor 1 phase | Power | kW | 0.25 | 0.55 | 0.55 | 0.55 | 0.75 | — |
| Voltage | V | 110~115 (60Hz),200~230 (50Hz) | — | |||||
| Speed | rpm | 1425(50Hz),1725(60Hz) | — | |||||
| Plug | North America, Europe, UK/Ireland, India | — | ||||||
| Motor 3 phase | Power | kW | — | 0.55 | 0.55 | 0.55 | 0.75 | 1.5 |
| Voltage | V | — | 200~230 or 380~415 (50Hz),200~230 or 460 (60Hz) | |||||
| Speed | rpm | — | 1425 (50Hz),1725 (60Hz) | |||||
| Inlet/Exhaust Flange | KF25/KF16 | KF40/KF16 | KF40/KF16*2 | |||||
| Dimensions | 1 phase | mm | 326*212*253 | 450*260*296 | 455*260*296 | 493*297*334 | 538*315*348 | — |
| 3 phase | mm | — | 450*260*296 | 455*260*296 | 493*297*334 | 538*315*348 | 576*450*402 | |
| Net Weight | 1 phase | kg | 15 | 21 | 22 | 29 | 36 | — |
| 3 phase | kg | — | 20 | 21 | 28 | 31 | 54 | |
| Cooling Type | Air cooled | |||||||
| Others | With air flush | |||||||
Features & Benefits
No oil clean vacuum.
No oil back-diffusion, no oil mist exhaust, provide clean vacuum environment
Wide product lineup.
Pumping speed covers 3~60 m3 /h, limited vacuum level 1~8 Pa
Suitable for all type of power supply around the world.
110/220/380/460V, 50/60Hz for choose
Low vibration, low noise.
57~65 dB(A), smooth operation
High efficiency, ease of maintenance.
No water cooled, no oil lubricated, no daily maintenance
Quality Control
CMM inspection system assures
fixed tolarance on dimension&shape
Pump Testing
Applications
Analyzing instrument and device.
Spectroscopy/scHangZhou electron microscopy.
Space environment simulation machine.
Helium Leak detector.
Mass spectrometer.
Cryopump regeneration.
Accelerators/synchrotrons.
Food and drug industry.
Freezing dryer.
Vacuum storage.
Medical equipment
Low temperature plasma sterilizer.
Vacuum storage.
Dental equipment.
Vacuum equipment.
Oil free ultrahigh vacuum unit
Oil free vacuum unit
Related Products
GWT25 Foreline Filter
Performance: Filter out the dust particles contained in the intake gas.
Application: Vacuum coating, food and drug processing, ceramic and glass manufacturing, vacuum CZPT and vacuum packaging systems.
GWS16 Exhaust Silencer
Performance: Reduce exhaust noise from oil-free vacuum systems.
Application: Installation of oil free scroll vacuum pumps requires a quiet vacuum system.
GWMMK150 Major Maintenance Kit
Performance: Prolong the service life of the product.
Application: For the major maintenance of oil free scroll vacuum pump GWSP150.
GWTSK150 Tip Seal Kit
Performance: Prolong the service life of the product.
Application: For the scheduled maintenance of oil free scroll vacuum pump GWSP150.
Company Profile
GEOWELL VACUUM CO.,LTD. is a HI-TECH enterprise in China dedicating in manufacturing, research and development, marketing of oil free scroll vacuum pumps and vacuum compressors since 2002. GEOWELL has been providing users and partners with premium quality products that are efficient and dependable, GEOWELL believe the integration of high performance and high reliability product and service will bring the highest value to both our customers and ourselves.
FAQ
Q: How long can I get the feedback after we sent the inquiry?
A: We will reply you within 12 hours in working day.
Q: Are you direct manufacturer?
A: Yes, we are direct manufacturer with factory and international department; we manufacture and sell all our products by ourselves.
Q: When can you delivery the product to us?
A: Since we are a factory with large warehouse, we have abundant products in store, so we can delivery within 7 days after get your deposit.
Q: Can I add logo to the products?
A: Of course, but we usually have quantity requirement. You can contact with us for details.
Q: How to guarantee the quality and after sales service of your products?
A: We conduct strict detection during production from raw material come in to product delivering shipment. Every product must go through 4 steps inspection from casting, machining, assembling, and performance testing within our factory before shipment, also intact packaging test are insured.
Q: What is your warranty term?
A: There is a 12 months warranty for our export products from the date of shipment. If warranty has run out, our customer should pay for the replacement part.
Q: Is the sample available?
A: Yes, usually we send our samples by Fedex, DHL, TNT, UPS, EMS, SF, Depon, it will take around 3 to 4 days for our customer receive them, but customer will charge all cost related to the samples, such as sample cost and air freight. We will refund our customer the sample cost after receiving the order.
/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1
| After-sales Service: | Yes |
|---|---|
| Warranty: | 1 Years |
| Oil or Not: | Oil Free |
| Customization: |
Available
|
|
|---|
.shipping-cost-tm .tm-status-off{background: none;padding:0;color: #1470cc}
| Shipping Cost:
Estimated freight per unit. |
about shipping cost and estimated delivery time. |
|---|
| Payment Method: |
|
|---|---|
|
Initial Payment Full Payment |
| Currency: | US$ |
|---|
| Return&refunds: | You can apply for a refund up to 30 days after receipt of the products. |
|---|
How to check the vacuum pump
A vacuum pump is a machine that draws gas molecules from a volume and maintains a partial vacuum. Its main job is to create a relative vacuum within the stated capabilities. If your vacuum pump isn’t working properly, it may need service. Read on to learn more about the types of vacuum pumps and how to check them.
Principle of industrial vacuum pump
Industrial vacuum pumps are used in industrial processes that require vacuum. These pumps are designed to generate, improve and maintain vacuum. Learn about the different types of industrial vacuum technology. You can start by reading about the most common types of industrial vacuum pumps. These pumps can be used in a variety of industrial processes from cleaning to manufacturing.
Regardless of the technology used to manufacture these pumps, the basic principles behind their operation are the same. The speed and mass flow of the pump will determine its capacity and suitability. A faster flow rate will minimize the time it takes for the machine to empty. Another important factor to consider is the type of vacuum you need.
A liquid ring vacuum pump is an industrial pump that uses a ring of liquid to form a seal. This type of pump is best suited for applications with high vapor loads and high liquid carry-over. Liquid ring vacuum pumps can be divided into two categories: liquid ring vacuum pumps and scroll vacuum pumps.
Industrial vacuum pumps work by removing gas molecules from a chamber. The partial vacuum created allows material to flow through the void. As more molecules are removed, the pressure in the chamber decreases, releasing energy that can be used for a variety of different purposes.
The most common use of industrial vacuum pumps is for electric lights. In these lamps, a vacuum pump removes the gas, causing the bulb to light up. Energy from the vacuum is also used in aircraft to power instruments. In addition to powering industrial vacuum cleaners, they are used in a variety of other environments.
High-performance industrial vacuum systems require specific materials that can withstand extreme pressure. This means that the materials used in these systems need to be properly checked. They must also be free of organic debris and other contaminants before they can be safely placed in the chamber.
Types of vacuum pumps
There are various types of vacuum pumps. Which one to choose should depend on the purpose of the pump and the degree of vacuum that must be achieved. It is mainly divided into three categories: rough vacuum or low vacuum, high vacuum and ultra-high vacuum. They all have varying degrees of scarcity. The higher the pressure, the fewer molecules per cubic centimeter. This in turn improves vacuum quality.
The vacuum pump is critical to the operation of the vacuum system. These devices are divided into three main categories according to their working pressure range. These pumps have different characteristics and technologies that make them ideal for specific applications. The choice of vacuum pump required for a particular application depends on how much vacuum you need, and how much power you are willing to spend.
Vacuum pumps are used in a variety of industrial and scientific processes. Their main function is to remove gas molecules from the sealed volume, leaving a partial vacuum. There are many different types of vacuum pumps, including rotary piston, liquid ring and scroll vacuum pumps. In addition, turbomolecular pumps are used.
Dry vacuum pumps are more expensive than wet vacuum pumps. Wet vacuum pumps use oil as their lubricating fluid. Different types of oils are used depending on the application. Some wet pumps have additional features, including contaminant filtration. However, wet systems have one major disadvantage: the contact between oil and fluid. To avoid this, oil separators are usually used.
There are several different types of vacuum pumps. The basic type is the positive displacement pump. It operates by expanding the chamber and removing gas molecules. The intake valve draws fluid into the chamber, while the exhaust valve opens when the chamber is at maximum expansion. This cycle repeats several times per second. Positive displacement pumps are often used in multistage vacuum systems. 
Maintenance of vacuum pump
Regular maintenance is very important to ensure the long-term effective use of the vacuum pump. One way to ensure proper pump performance is to change the oil regularly. Pump oil may be contaminated by vapor condensation. To avoid this problem, close the inlet valve for 20 to 30 minutes before applying vacuum. It is also important to install an inlet cold trap to protect the pump from corrosive vapors.
Another way to prolong the life of your vacuum pump is to periodically remove any solvent in it. This step reduces internal corrosion and prevents premature pump failure. During maintenance, be sure to disconnect the power supply to the vacuum pump. After cleaning, store it in a dry and safe place. The pump should also be disposed of in accordance with local regulations.
Vacuum pumps may require frequent oil changes, especially when used in wet chemistry. The standard rule is to change the oil after 3,000 hours of use, but some pumps require more frequent oil changes. It is also important to clean the oil regularly, as dirty or discolored oil can affect the performance of the pump.
Vacuum pumps are often equipped with on-site glass to allow the user to visually check the oil level. Clean oil will appear transparent, while dirty oil will appear darker. Frequent oil changes are essential, as oil changes can help spot various potential problems. Changes in vacuum pump performance or strange noises are also good indicators of a problem.
After an oil change, the vacuum pump should be cleaned thoroughly with a soft cloth and mild degreaser. Oil changes should take less than ten minutes, and they will extend the life of your equipment. Additionally, the outside of the pump should be wiped with a cloth or rag.
The pump must be properly vented to avoid internal corrosion. If possible, place the pump away from hot equipment or rooms. Overheating can reduce the viscosity of the oil and cause premature pump failure. In addition, it can lead to overwork of other expensive scientific equipment. Heat can also cause cracked rubber parts and oil leaks. 
Signs of damage to the vacuum pump
A bad vacuum pump can cause a variety of automotive problems, including poor fuel economy, difficult braking, undercarriage oil leaks, and faulty air conditioning. If any of these problems occur, call a mechanic to check your vehicle’s vacuum pump. You can also check the air conditioner and brake pedal to see if they are working properly.
A loud noise from the pump can also be a symptom of a malfunction. These noises are often caused by the aging and accumulated wear of specific components. If this is the case, the diaphragm, valve plate or seals may need to be replaced. However, if the noise is coming from bearings or other areas, more extensive repairs may be required. Additionally, dust and other contaminants can enter the pump chamber, which can degrade pump performance.
If the vacuum pump won’t start, it could be a blown fuse or a power or voltage problem. Other common causes are flow restrictions or improper installation at the entrance. Also, the vacuum pump may be damaged or the capacitors may be of poor quality. It’s not always easy to tell if a vacuum pump is leaking oil, but a greasy transmission can indicate a vacuum pump failure.
A leaking vacuum pump can also hiss when the car’s engine is running. If you hear it, check the hoses and connections to make sure there are no leaks. A vacuum leak may indicate a faulty vacuum pump, so you need to replace it as soon as possible.
Checking end pressure is easy, but a pressure gauge can also serve as a sign. You can also check for pump vibration by running a short procedure. Excessive vibration can be subtle, but it can greatly affect your process. If you notice excessive pump vibration, you should contact a professional immediately.
Poor pump performance can cause many problems for your company. A bad vacuum pump not only wastes material, it also damages your tools and reputation.
editor by Dream 2024-05-15
China Hot selling Electric Oil Free Small Vacuum Pump 500W Flow Rate Vacuum Pump Piston Type AC Vacuum Pump for Dental wholesaler
Product Description
Product Parameters
| ITEM NO | HC750A2-1 |
| Name | AC oil free vacuum pump |
| Packing | 1 pcs / carton case |
| Dimension | 271*128*216 mm |
| Weight | 10.6kg |
| vacuum flow rate | 120 L/min @-92Kpa : (One-Grade vacuum) 60 L/min @-98Kpa :(Two-Grade vacuum ) |
| Voltage | 220V 50Hz/110V 60Hz; |
| Power | 500W |
| Noise | ≤51dB(A) |
| Speed | 1440rpm / 1700rpm ; |
| Temperature | -5ºC-40ºC |
| Thermal protector | 135ºC |
| Accessories | With Power cord, handle, footpads, silencer |
Detailed Photos
Our Advantages
Company Profile
Our Customer
Certifications
Packaging & Shipping
FAQ
Q.1: What’s your factory address ? May I visit your factory ?
Our factory is located in HangZhou city, ZHangZhoug province, near to HangZhou, ZheJiang and HangZhou, about 2 hours by bus or train.Welcome to visit our factory.
Q.2: When I get my products, is there anything I should pay attention to ?
It need to clear the filter once every 2 months.
When use it, it need to handle with care and pay more attention to waterproof.
Q.3 : Can I buy the sample to test?
We are pleased to send the samples for your evaluation.And the samples shipping freight can be return back to you with next bulk order .
Q.4: Do you have test records of every pump?
We will inspect products 3 times before shipment and every pump have the test records. We will keep these test records to our quality traceability system about 3-5 years.
Test items : workmanship, air flow rate, power, vacuum pressure, current, noise, vibration , temperature and durability etc.
Q.5:How long is the life of the your pump?
“Quality is our culture”, our vacuum pump with long life (20000 hours ) and high quality ( stable air flow, import spare parts,
high workmanship etc ).
Q.6: What’s your warranty?
Our warranty is 2 years.It means that if our machine has any problems within 2 years, we will send you new 1 or free spare parts for your replacement.
Q.7: Question : How many years of your factory?
Our factory has the production experience more than 20 years.
We make main spare parts of vacum pump by ourselves (include the motor), so we can control the pumps quality very well
Q.8: Question: Can you produce products same/ similar with mine?
We have professional and experienced R & D team, so we can better serve customers to achieve high-end customization and development. We accept the ODM and OEM.
| After-sales Service: | Online Support |
|---|---|
| Warranty: | 2years |
| Oil or Not: | Oil Free |
| Structure: | Portable Vacuum Pump |
| Exhauster Method: | Piston Vacuum Pump |
| Vacuum Degree: | Vacuum |
| Samples: |
US$ 142/Piece
1 Piece(Min.Order) | |
|---|
| Customization: |
Available
|
|
|---|
Types of vacuum pumps
A vacuum pump is a device that draws gas molecules from a sealed volume and leaves a partial vacuum in its wake. Its job is to create a relative vacuum within a specific volume or volume. There are many types of vacuum pumps, including centrifugal, screw and diaphragm.
Forward centrifugal pump
Positive displacement centrifugal vacuum pumps are one of the most commonly used pump types in the oil and gas industry. Their efficiency is limited to a range of materials and can handle relatively high solids concentrations. However, using these pumps has some advantages over other types of pumps.
Positive displacement pumps have an enlarged cavity on the suction side and a reduced cavity on the discharge side. This makes them ideal for applications involving high viscosity fluids and high pressures. Their design makes it possible to precisely measure and control the amount of liquid pumped. Positive displacement pumps are also ideal for applications requiring precise metering.
Positive displacement pumps are superior to centrifugal pumps in several ways. They can handle higher viscosity materials than centrifuges. These pumps also operate at lower speeds than centrifugal pumps, which makes them more suitable for certain applications. Positive displacement pumps are also less prone to wear.
Positive displacement vacuum pumps operate by drawing fluid into a chamber and expanding it to a larger volume, then venting it to the atmosphere. This process happens several times per second. When maximum expansion is reached, the intake valve closes, the exhaust valve opens, and fluid is ejected. Positive displacement vacuum pumps are highly efficient and commonly used in many industries.
Self-priming centrifugal pump
Self-priming centrifugal pumps are designed with a water reservoir to help remove air from the pump. This water is then recirculated throughout the pump, allowing the pump to run without air. The water reservoir can be located above or in front of the impeller. The pump can then reserve water for the initial start.
The casing of the pump contains an increasingly larger channel forming a cavity retainer and semi-double volute. When water enters the pump through channel A, it flows back to the impeller through channels B-C. When the pump is started a second time, the water in the pump body will be recirculated back through the impeller. This recycling process happens automatically.
These pumps are available in a variety of models and materials. They feature special stainless steel castings that are corrosion and wear-resistant. They can be used in high-pressure applications and their design eliminates the need for inlet check valves and intermediate valves. They can also be equipped with long intake pipes, which do not require activation.
Self-priming centrifugal pumps are designed to run on their own, but there are some limitations. They cannot operate without a liquid source. A foot valve or external liquid source can help you start the self-priming pump.
Screw Pump
The mechanical and thermal characteristics of a screw vacuum pump are critical to its operation. They feature a small gap between the rotor and stator to minimize backflow and thermal growth. Temperature is a key factor in their performance, so they have an internal cooling system that uses water that circulates through the pump’s stator channels. The pump is equipped with a thermostatically controlled valve to regulate the water flow. Also includes a thermostatic switch for thermal control.
Screw vacuum pumps work by trapping gas in the space between the rotor and the housing. The gas is then moved to the exhaust port, where it is expelled at atmospheric pressure. The tapered discharge end of the screw further reduces the volume of gas trapped in the chamber. These two factors allow the pump to work efficiently and safely.
Screw vacuum pumps are designed for a variety of applications. In some applications, the pump needs to operate at very low pressures, such as when pumping large volumes of air. For this application, the SCREWLINE SP pump is ideal. Their low discharge temperature and direct pumping path ensure industrial process uptime. These pumps also feature non-contact shaft seals to reduce mechanical wear. Additionally, they feature a special cantilever bearing arrangement to eliminate potential sources of bearing failure and lubrication contamination.
Screw vacuum pumps use an air-cooled screw to generate a vacuum. They are compact, and clean, and have a remote monitoring system with built-in intelligence. By using the app, users can monitor pump performance remotely.
Diaphragm Pump
Diaphragm vacuum pumps are one of the most common types of vacuum pumps found in laboratories and manufacturing facilities. The diaphragm is an elastomeric membrane held in place around the outer diameter. While it is not possible to seal a diaphragm vacuum pump, there are ways to alleviate the problems associated with this design.
Diaphragm vacuum pumps are versatile and can be used in a variety of clean vacuum applications. These pumps are commercially available with a built-in valve system, but they can also be modified to include one. Because diaphragm pumps are so versatile, it’s important to choose the right type for the job. Understanding how pumps work will help you match the right pump to the right application.
Diaphragm vacuum pumps offer a wide range of advantages, including an extremely long service life. Most diaphragm pumps can last up to ten thousand hours. However, they may be inefficient for processes that require deep vacuum, in which case alternative technologies may be required. Additionally, due to the physics of diaphragm pumps, the size of these pumps may be limited. Also, they are not suitable for high-speed pumping.
Diaphragm vacuum pumps are a versatile subset of laboratory pumps. They are popular for their oil-free construction and low maintenance operation. They are available in a variety of styles and have many optional features. In addition to low maintenance operation, they are chemically resistant and can be used with a variety of sample types. However, diaphragm pumps tend to have lower displacements than other vacuum pumps.
Atmospheric pressure is a key factor in a vacuum pump system
Atmospheric pressure is the pressure created by the collision of air molecules. The more they collide, the greater the pressure. This applies to pure gases and mixtures. When you measure atmospheric pressure, the pressure gauge reads about 14.7 psia. The higher the pressure, the greater the force on the gas molecules.
The gas entering the vacuum pump system is below atmospheric pressure and may contain entrained liquids. The mechanism of this process can be explained by molecular kinetic energy theory. The theory assumes that gas molecules in the atmosphere have high velocities. The resulting gas molecules will then start moving in random directions, colliding with each other and creating pressure on the walls of the vacuum vessel.
Atmospheric pressure is a critical factor in a vacuum pump system. A vacuum pump system is useless without proper atmospheric pressure measurement. The pressure in the atmosphere is the total pressure of all gases, including nitrogen and oxygen. Using total pressure instead of partial pressure can cause problems. The thermal conductivity of various gases varies widely, so working at full pressure can be dangerous.
When choosing a vacuum pump, consider its operating range. Some pumps operate at low atmospheric pressure, while others are designed to operate at high or ultra-high pressure. Different types of pumps employ different technologies that enhance their unique advantages.
The screw pump is less efficient in pumping gases with smaller molecular weight
Vacuuming requires a high-quality pump. This type of pump must be able to pump gas of high purity and very low pressure. Screw pumps can be used in laboratory applications and are more efficient when pumping small molecular weight gases. Chemical resistance is critical to pump life. Chemical resistant materials are also available. Chemically resistant wetted materials minimize wear.
Gear pumps are more efficient than screw pumps, but are less efficient when pumping lower molecular weight gases. Gear pumps also require a larger motor to achieve the same pumping capacity. Compared to gear pumps, progressive cavity pumps also have lower noise levels and longer service life. In addition, gear pumps have a large footprint and are not suitable for tight spaces.
Progressive cavity pumps have two or three screws and a housing and side cover. They are also equipped with gears and bearings. Their mechanical design allows them to operate in high pressure environments with extremely low noise. The progressive cavity pump is a versatile pump that can be used in a variety of applications.
Dry screw compressors have different aspect ratios and can operate at high and low pressures. The maximum allowable differential pressure for screw compressors ranges from 0.4 MPa for 3/5 rotors to 1.5 MPa for 4/6 rotors. These numbers need to be determined on a case-by-case basis.
editor by CX 2023-05-10
china supplier Industrial Sliding Oil Sealed Rotary Vane Type 2X Series (2X-4, 2X-8, 2X-15, 2X-30, 2X-70) Double Stage Electric Belt Vacuum Pump for Vacuum Metallizing Machine manufacturers
Solution Description
2X variety rotary vane vacuum pump is a basic tools utilized to extract the gasoline in a distinct sealed container, so that the container can receive a particular vacuum. Thanks to the substantial advancement of modern science and technology, vacuum pumps are used in CZPT scientific fields and CZPT enterprises and undertakings. It can be employed for scientific investigation, creation and educating in scientific study establishments, faculties and universities, industrial and mining enterprises in metallurgy, chemical business, gentle market, petroleum, healthcare, pharmaceutical, printing and dyeing, electrical appliances, electrical vacuum, semiconductor, food, atomic vitality, textile, and so forth.
Product Photographs:
Structure Description:
Figure 1 is a schematic diagram of a rotary vane vacuum pump. The rotors 3 and 7 are tangent to the higher vacuum chamber 1 and the minimal vacuum chamber 6. The rotors 3 and 7 rotate in the course of the arrow, which drives the rotor sliding in the rotor slot to rotate. Because the spring 9 And the motion of centrifugal force, the outer finish of the rotor slides in opposition to the internal surface area of the high and minimal vacuum chambers, and the moon-formed area fashioned by the rotor and the large and lower vacuum chambers is moved from the intake nozzle 2 to the exhaust valve 5 and from the air pipe 4 to the exhaust. The valve 10 is separated to kind two or three volumes, and the dimensions modifications periodically. When the rotary vane vacuum pump proceeds to rotate at the position shown in the determine, the volumes of A and C progressively improve, and the pumped quantity fuel does not enter the air. The nozzle enters the pump, and at the same time, the volume of B and D slowly decreases, and the force rises. Then, the exhaust valves 5 and ten are opened to discharge the fuel out of the vacuum chamber. valve, so it can avoid the gasoline from returning to the vacuum chamber. When the pumping stress is high, the valves of the high and minimal vacuum chambers are exhausted, which is equal to a one-stage pump. When the vacuum degree is high, all the gas enters the vacuum chamber and is then fatigued by the exhaust valve ten. Enter the two-stage pump to perform.
For case in point, when the extracted fuel contains substantial vapor gasoline, when the gasoline is compressed and the partial pressure of its vapor exceeds the saturation stress of the vapor at the temperature of the pump, the vapor is compressed into liquid at this time, and the rotary vane vacuum pump It cannot be discharged, but is mixed in the vacuum oil, which greatly minimizes the functionality of the pump. If a proper amount of air is blended in, so that when the steam is compressed, its partial force is also decrease than the saturated stress of the pump temperature, the steam can be discharged out of the pump before it gets to be liquid, so this collection of pumps over 2X-4 All are geared up with aeration valve 11 that can put in a specified quantity of gas, see Figure 1
The form and construction of CZPT vacuum pumps of the 2X sequence are essentially the very same. The pump is pushed by the motor to the rotor by means of the V-belt. The motor and pump are CZPT ened to the chassis with screw clips.
2X rotary vane vacuum pump is composed of pump physique, high rotor, minimal rotor, CZPT finish plate, rear stop plate, substantial rotor plate, minimal rotor plate, exhaust valve, exhaust hood, sight glass and other elements. See Determine 2 and Determine 3.
A middle partition is pressed into the 2X rotary vane vacuum pump, and the vacuum pump casing is divided into large and lower vacuum chambers. The CZPT end of the large rotor protrudes from the CZPT axle the rear conclude protrudes from the rear axle. The CZPT axle is supported by bearings in the CZPT plate, by means of the oil-limited chamber and out of the CZPT plate: the rear axle is supported by bearings in the center bulkhead. Whilst extending into the low vacuum chamber, the low vacuum chamber rotor is put in on the rear axle, so the high and reduced rotors are driven by the CZPT axle. Both the substantial and lower rotors have bisected slots, and the “T”-shaped rotary vanes are supported by springs and mounted in the slots. The air inlet of the 2X rotary vane vacuum pump has a filter display, and the exhaust port has an oil blocking monitor. There is an air aeration valve on the still left facet of the sight glass and an oil drain plug on the base.
2X rotary vane vacuum pump pumping approach: as proven in Determine 2, the gas enters the large vacuum chamber from the ingestion nozzle. At 1st, the higher stress is strong, the higher and minimal vacuum chambers are stuffed with environment, and each exhaust valves are opened to exhaust. As the pumping progresses, the air pressure decreases (that is, the vacuum diploma boosts), the stress of the higher vacuum chamber is not adequate to push the exhaust valve, and the gasoline enters the lower vacuum chamber through the middle partition, and the pressure is not adequate to press the exhaust valve at this time, but The lower vacuum chamber enters a specified volume of oil, which assists to open the exhaust valve, and the fuel is also discharged. The discharged gas is mixed with oil particles, and the oil is divided by filtering the oil screen. Only the gasoline is discharged from the pump. The fuel path is shown in Determine 2.
The oil in the oil sealing chamber of the 2X rotary vane vacuum pump is equipped from the oil pool A by means of the hole on the CZPT stop plate. The oil in the minimal vacuum chamber is supplied from the oil pool A via the gap in the rear end plate. The oil in the high vacuum chamber is circulated and supplied from the holes in the center partition. The sealing of the CZPT and rear handles of the 2X rotary vane vacuum pump is manufactured by the oil pool B on the upper part of the pump entire body flowing into the oil groove through the gap of the end experience chamber of the pump body for sealing.
Product functionality and parameters:
Merchandise Software:
one. Owing to the high development of modern day science and technological innovation, rotary vane vacuum pumps are used in CZPT scientific fields and CZPT enterprises and undertakings. It can be employed for scientific research, manufacturing and instructing in scientific study institutions, colleges and universities, industrial and mining enterprises in metallurgy, chemical sector, gentle sector, petroleum, medical, pharmaceutical, printing and dyeing, electrical appliances, electric powered vacuum, semiconductor, foods, atomic power, textile, etc.
two. Because the rotary vane vacuum pump is manufactured of ferrous metallic and is reasonably specific, the function of the total pump is linked with each other, so the rotary vane vacuum pump is not appropriate for pumping out large-oxygen, toxic and explosive supplies. Various gases that corrode ferrous metals and have chemical results on vacuum oil can not be utilised as compressors and transfer pumps. If there is a pump with a fuel ballast device, a certain amount of condensable gas can be taken off. ,
three. The rotary vane vacuum pump can be employed to directly get vacuum operations with a vacuum degree beneath 10~3 Torr, as nicely as to cooperate with other vacuum functions.
4. Rotary vane vacuum pumps are typically utilised in an environment the place the area temperature is not reduced than 5°C and the relative temperature is not higher than 90%.
Solution Functions:
one. Vast range of free-air capacities to match certain programs
two. Constructive strain oil method assures proper lubrication and prevents oil starvation underneath substantial fuel loads
3. CZPT performing inlet valve shields inside components from oil and air contamination if the pump stops while under vacuum
four. Fuel ballast valve boundaries internal condensation Allows you use pump when condensable vapors are current.
Company Profile:
Diaphragm oil-free pumps for glass, stainless metal, and plastic dryers. The hydrophobic PTFE in-line filter membrane is in place and includes particles bigger than .1 microns. The pump features 1/8 HP, optimum force of 50 PSI, and a highest temperature of 38°C to avoid fluid and air contamination, as well as exhaust backup. The pump attributes oil-free procedure, rugged development, effortless hose connections, and a greatest constant stress of 50 PSIG. Characteristics Vacuum pump guards against all fluid and air contamination Can be utilized to stop harmful exhaust backup Oil-totally free procedure Rugged development/low routine maintenance 50 PSIG greatest constant stress